定期检查滚子徐州SKF轴承对于保持轴承的**佳状态和反映发现的问题非常重要。轴承使用注意事项及相关知识。

Regular inspection of roller Xuzhou SKF bearings is very important to keep the bearings in good condition and to reflect the problems found. Matters needing attention in the use of bearings and related knowLEDge.

首先，我们应该强调保持滚子轴承润滑和清洁的重要性。因此，在检查轴承之前，首先清洗轴承表面，然后去除轴承周围的零件。油封是一个非常脆弱的部分。在检查和拆卸过程中，应注意不要施加太大的力以免损坏零件。然后仔细检查滚子轴承及其周围部件的油封。如果有任何不好的症状，必*须更换。油封不*良会导致轴承损坏，使滚子徐州SKF轴承浑浊异常，导致设备停机。

First of all, we should emphasize the importance of keeping roller bearings lubricated and clean. Therefore, before inspecting the bearing, first clean the bearing su-ce, and then remove the parts around the bearing. Oil seal is a very fragile part. During inspection and disassembly, care should be taken not to exert too much force to avoid damage to parts. Then carefully inspect the oil seals of roller bearings and their surrounding parts. If there are any bad symptoms, they must be replaced. Poor oil seal will lead to bearing damage, make the SKF bearing turbidity abnormal roller Xuzhou, leading to equipment shutdown.

其次，我们还需要检查滚子轴承的润滑油。润滑不仅对轴承，而且对所有进口轴承都非常重要。但是请注意，给轴承加太多的润滑脂是不明智的。

Secondly, we also need to check the lubricating oil of roller bearings. Lubrication is very important not only for bearings, but also for all imported bearings. But please note that it is not wise to add too much grease to bearings.

滚子轴承润滑剂的检验方法如下：

The inspection methods for roller bearing lubricants are as follows:

在手指间擦一点油。如果有污染物，摸摸。或在手背上涂一层薄薄的润滑剂来检查密封。

Rub a little oil between your fingers. If there are contaminants, feel them. Or apply a thin layer of lubricant on the back of your hand to check the seal.

然后更换滚子徐州SKF轴承的润滑油。

Then change the lubricating oil of Xuzhou SKF bearing.

带润滑剂的滚子轴承应该充满新鲜油，如果可能的话，在排出旧油后以低速旋转几分钟。使油收集尽可能多的残留污染物，然后去除油。注：使用前应过滤机油。当用润滑脂替换轴承中的润滑脂时，所用的分离器应避免棉和轴承的任何部分之间的任何接触。由于这些残留的纤维可能楔入轧件之间并造成损伤，特别是在小轴承的应用中，应更加注意这个问题。

Roller bearings with lubricants should be filled with fresh oil and, if possible, rotate at a low speed for a few minutes after discharging the old oil. Make the oil collect as many residual pollutants as possible, and then remove the oil. Note: The oil should be filtered before use. When replacing grease in bearings with grease, the separator used should avoid any contact between cotton and any part of the bearing. As these residual fibers may wedge between the rolled parts and cause damage, especially in the application of small bearings, more attention should be paid to this problem.

经过一段时间的运动，振动和噪声保持在一定的水平，频谱非常单一，只有频率的一到两倍。三倍工频以上的频谱很少出现。滚动徐州SKF轴承处于非常稳定的状态，已经进入了稳定的工作循环。

After a period of movement, the vibration and noise remain at a certain level, the spectrum is very single, only one or two times the frequency. Frequency spectrum above triple power frequency rarely appears. The rolling Xuzhou SKF bearing is in a very stable state and has entered a stable working cycle.

连续运行后，轴承振动和噪声开始增加，有时出现异常声音，但振动增加缓慢。此时，角接触球轴承的峰值开始突然达到一定值。我们认为，轴承的特征是它在这个时候的初始失效。

After continuous operation, bearing vibration and noise begin to increase, sometimes abnormal sound occurs, but vibration increases slowly. At this time, the peak value of angular contact ball bearings begins to suddenly reach a certain value. We believe that the bearing is characterized by its initial failure at this time.

文章来自：徐州SKF轴承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章来自：徐州INA轴承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章来自：徐州NSK轴承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

QQ：524085168

电话：0510-81207777

手机：13311666672/13395185757